GAT-AQ is GardenAgroTech’s free spray application and calibration tool for backpack and boom sprayers, nozzle checks, product quantities, and preliminary drone planning. Available in English, Spanish, Portuguese, French, and German. Use measured field values and follow product labels and local regulations.
Sprayer calibration, nozzle checks, product quantities, row/band treated area, and drone beta flow checks. Replace sample values with measured field values.
Boom Sprayer Calibration
Use measured nozzle output, speed, and spacing to compare actual spray rate against target.
Help me measure this
- Measure speed over a known distance in the same gear, RPM, pressure, and field conditions you will spray in.
- Collect one nozzle output for one minute at working pressure, then enter the measured L/min or GPM.
- Nozzle spacing is the distance between adjacent nozzles on the boom.
- Sample values are only placeholders, not recommendations.
Measured field inputs
Backpack / Knapsack Calibration
Measure a walking test and collected output to calculate spray volume and tank coverage.
Help me measure this / 1/128 acre explained
- Metric method: spray a measured strip. Area = spray width × test distance. The calculator converts volume used over that area into L/ha.
- Imperial 1/128 acre method: 1 acre has 128 × 340.3 ft². Because 1 gallon has 128 fl oz, fl oz collected over 1/128 acre directly equals GPA.
- For imperial users: required walking distance in feet = 340.3 ÷ spray width in feet. If width is 2 ft, walk about 170 ft.
- Keep walking speed, nozzle height, pressure, and spray pattern consistent.
Walking and spray test
Row / Bed / Band Treated Area
Use when only part of the field or bed is treated. Prevents calculating product on total area by mistake.
Help me measure row, bed, or band treatment
- Use this only when the product label allows banded/row application.
- Treated area = total area × treated band width ÷ row or bed spacing.
- Example: 0.5 m treated band on 1.5 m row spacing means only 33.3% of the total area is treated.
- This helps prevent accidentally dosing the full field when only the crop row or bed strip is sprayed.
Treated area inputs
Product Quantity & Tank Load Builder
Calculates product quantities from user-entered label rates. Add one product, several products, or an adjuvant, then review per full tank, total job, and final partial tank quantities.
What this section calculates
- This is a quantity calculator. It converts user-entered label rates into product per tank and total product for the job.
- You can add several product cards, but the calculator does not confirm whether the products can legally or safely be mixed together.
- Use per area for products labeled per ha or per acre. Use per 100 L / 100 gal of spray mixture for adjuvants or products labeled per spray-mixture volume.
- For true compatibility, always check the product label, supplier guidance, water quality, pH, jar test, and local regulations.
Job, tank and product inputs
This calculator only calculates quantities from user-entered label rates. It does not confirm compatibility, crop/use approval, tank-mix legality, water quality suitability, pH suitability, adjuvant suitability, or mixing safety.
Nozzle Output & Uniformity Check
Enter collected output from each nozzle. Values outside the selected comparison range are flagged.
How to perform this test
- Run clean water through the sprayer at normal working pressure.
- Collect each nozzle for the same selected time.
- Enter the collected volume for each nozzle.
- Example: if Nozzle 1 produces 500 ml during a 60-second test, enter 500.
- GAT-AQ compares each entered nozzle with the group average. This checks nozzle-to-nozzle uniformity; it does not compare output with the manufacturer-rated nozzle flow.
Nozzle output readings
Drone Beta: Flow & Effective Swath Checker
Beta module for required flow, flow per outlet, flight-line spacing, area per tank and tank loads. Use a measured effective swath from an appropriate swath/deposition test, not the advertised maximum spray width.
Drone beta help
- Operational pass-to-pass width established from a swath/deposition test. This value is used both as the width in the required-flow calculation and as the flight-line spacing.
- Do not apply an additional overlap percentage. The measured effective swath already represents the operational pass-to-pass width used by this calculation.
- L/min = L/ha × speed km/h × effective swath m ÷ 600
- If metric speed is entered as m/s, the corrected formula uses ÷166.67.
- GPM = GPA × speed mph × effective swath ft ÷ 495
- This beta does not confirm legal permission, drift safety, battery planning, or label approval for UAV/aerial application.
Drone spray inputs
Drone spraying may require aviation permissions, product-label approval for aerial/UAV use, and local compliance.
This calculator is a mathematical planning tool only. The pesticide label and local regulations always override calculator outputs.
Saved setup tools
Save and load the current module in this browser, or export/import a JSON setup file for offline backup.
GAT-AQ — Practical Spray Planning and Calibration
Accurate spray application begins with reliable field measurements. Use GAT-AQ to support sprayer calibration, check application volumes, calculate product quantities, and plan treated areas. Recheck your calculations whenever equipment settings, operating conditions, or application requirements change.
Important: GAT-AQ is a mathematical planning and calibration tool, not a substitute for pesticide label instructions, equipment testing, or regulatory compliance. Always follow the product label, use appropriate personal protective equipment (PPE), and verify application requirements before spraying.

